Ученые создали микровентили для медицинских катетеров, блокирующие обратный ток жидкости

A single cough, deep breath, or shift in posture can turn life-saving medical microcatheters into hazardous two-way streets. When doctors deliver delicate therapies into sensitive targets such as the brain, retina, or inner ear, they depend on slender tubes narrower than three human hairs. Yet at these sub-millimeter scales, everyday bodily pressure fluctuations easily force blood, debris, and tissue backward into the channel, causing sudden blockages, contaminating drug reservoirs, and abruptly cutting off therapy. Scientists developed a strategy to mitigate this backflow hazard by sculpting tiny and self-regulating "liquid diodes" directly inside the ultra-narrow tips of flexible catheters. Published in the International Journal of Extreme Manufacturing, Prof. Zhuo-Chen Ma, Prof. Bing Han and their co-workers at Shanghai Jiao Tong University and Beijing Institute of Technology inscribed three-dimensional Tesla microvalves inside 100-micrometer channels using ultrashort laser pulses. The passive architecture suppresses reverse pressure surges by 73.5% during flow initiation and 82.0% during flow shutdown, regulating fluid entirely through geometry without needing moving flaps, batteries, or electronic sensors. Stopping backflow in artificial micro-conduits has long presented a stubborn physics and engineering bottleneck. While human veins rely on flexible, flapping leaflets to keep blood moving forward, artificial moving parts built at the scale of a single hair cell quickly jam, suffer material fatigue, and fail. Traditional passive valves, which use looping channels to resist reverse motion, also fail inside ultra-thin tubes. At microscopic dimensions, liquids move in a low-speed regime where fluid behaves less like rushing water and more like thick syrup, creeping symmetrically through channels without producing the turbulence required to block reverse flow. Manufacturing these structures inside slender, flexible tubing posed an equally stubborn barrier: fragile tubes bend and sag under the microscope, causing 3D-printing lasers to miss their focal mark, cure unevenly, and detach under pressure. The team conquered these barriers by pairing an optical alignment algorithm with an energy-dissipating micro-architecture. To overcome the physical sagging of the flexible tubes, the team devised the Concentric Diffraction Ring-based Axial Alignment Algorithm (CAAA). By reading the circular, target-like light diffraction patterns naturally reflected through the catheter's cylindrical tip, the algorithm precisely pinpoints the tube's 3D tilt and instantly recalculates the laser toolpath to match it. A high-precision femtosecond laser then uses pulses of light to directly solidify liquid resin into complex 3D valves along the curved inner wall, achieving an alignment accuracy within one degree and a 90% fabrication success rate. The resulting microvalve acts as an intelligent and passive liquid brake. When medication flows forward, it cruises smoothly down a central lane with minimal resistance. But when bodily pressure tries to force fluid backward, the valve's 45-degree channels split the reverse stream and steer it into tight loops. These looping streams crash head-on into the incoming reverse flow, generating localized fluid whirlpools that choke off the channel and generate up to 2.2 times higher resistance in reverse than in forward motion. Crucially, the valve double-functions as a physical gatekeeper against biological contamination. In five-day laboratory trials with proliferating human HepG2 cells, standard open catheters clogged completely as dense tissue grew into the opening. By contrast, catheters bearing the laser-carved microvalves remained completely clear, restricting cell growth strictly to the outer shell. Even when subjected to five minutes of direct backward suction in fluid thick with cellular debris, the valve-protected channels stayed clear while conventional open needles choked instantly. This on-tip laser integration method provides a direct blueprint for building smart and self-regulating microfluidics into ultra-thin medical devices without complex mechanical assembly. By requiring no external actuation or control for the valve itself, power cables, and delicate mechanical flaps, the design eliminates the most common failure points in chronic drug delivery. To move toward clinical adoption, future research will assess how the printed polymer withstands prolonged pressure pulsing in living tissue, evaluate long-term chemical durability in biological fluids, and validate anti-fouling performance against brain-specific neuronal and glial cells in animal models. International Journal of Extreme Manufacturing (IJEM, IF: 25.1) is devoted to publishing articles of the highest quality and significance to pushing the limits of scales, precision, performance and environments in manufacturing. Maintained #1 in Engineering, Manufacturing for 4 consecutive years Average time to First Decision after Peer Review: 34 days Open Access Publishing Visit our webpage, like us on Facebook, and follow us on Twitter /Public Release. This material from the originating organization/author(s) might be of the point-in-time nature, and edited for clarity, style and length. Mirage.News does not take institutional positions or sides, and all views, positions, and conclusions expressed herein are solely those of the author(s).View in full here.